![]()
This would be a very nice new sensor: check overall Proliant Health. #HP ILO FIRMWARE DOWNLOAD DL380 G4 POWER SOFTWARE#You can download the installers for the required software here: I don't have the WBEM provider installed on any of my Windows 2003 servers, so, it appears this is a must for Windows 2008, or at least with 2008 R2. Once installed, now PRTG can get SNMP data from the RAID controller. To download the proper driver, first choose your operating system, then find your device name and click the download button. #HP ILO FIRMWARE DOWNLOAD DL380 G4 POWER DRIVERS#This page contains the list of device drivers for HP ProLiant D元80 G4. ![]() Download the latest drivers for your HP ProLiant D元80 G4 to keep your Computer up-to-date. HPE Integrated Lights Out (iLO) Server Management Overview. Power your enterprise with proven, industry-leading IT infrastructure products and software from Hewlett Packard Enterprise. Get iLO licensing details or download a free trial. #HP ILO FIRMWARE DOWNLOAD DL380 G4 POWER INSTALL#After consulting with HP, they had me to also install the Insight Management WBEM providers agent. After doing so, PRTG was able to configure sensors for just about everything except the Smart Array controller and it's drives. But we got this note from a customer: I did install the HP Insight Management Agents on my Windows 2008 R2 servers along with HP System Management Homepage. On my system l find the board assembly number and replacement part number at the edge of the system board under the pci raid controller.This article applies to PRTG Network Monitor 12 or later HP ProLiant system health sensors They are now included out of the box in PRTG (works for Windows drivers and most Linux drivers). ![]() Would it be beneficial for me to get the dual core CPU that it says it supports? Also since there are more dual core socket 604 CPU's available would the board support a non-listed one like this one? Thank you for looking, Shelby The HP ProLiant D元80 Generation 4 Server Maintenance and Service Guide can be found at On page 9 of this document: Under processors '2.83-GHz Intel® Xeon™ dual core, 1066-MHz FSB, 4-MB cache (for use with dual core processor SCSI system board assembly number 012863-001 only)' under system boards 'a) System board, single-core processor support, with processor cages and system battery - replacement part no.:399133-001.' 'b) System board, dual-core processor support, SCSI, with processor cages and system battery (for use with Intel® Xeon™ dual-core processor only) - replacement part no.: 404715-001 or 411028-001' To install dual core processors you would need a dl380g4 system board assembly number 012863-001 that has a replacement part number 404715-001 or 411028-001. Support List: Current CPU: The Hp site only lists one dual core CPU as being supported. OS installation: I had difficulty burning a SmartStart CD (bad media, and no spare - fresh - discs with me), so I reset NVRAM & BIOS defaults from BIOS setup and booted from the W2K8 R2 std 圆4 DVD, and away we went. ![]() It turned out that the iLO had new firmware available and the RAID controller, as well. My next step was to ensure that the firmware was up to date, so I burned the latest HP firmware DVD (luckily, another D元80 G4 had a DVD-ROM installed, so I swapped the CD-ROM in this one for the DVD drive) and booted the server from it. Physical installation: I racked the server easily enough, connected both onboard NICs and the iLO to the three 10/100/1000 unmanaged switches in the cabinet, and connected a set of KVM cables. #HP ILO FIRMWARE DOWNLOAD DL380 G4 POWER PATCH#Thinking toward the future, I decided that the best route to take would be to just go 64-bit, and as Microsoft saw fit to not release a W2K3 patch for a known memory leak exposed in the Blackberry Enterprise Server 5 platform, W2K8 seemed to be the only remaining choice. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |